Flipklok
 
Loading...
Searching...
No Matches
gpio.c
Go to the documentation of this file.
1/*
2 * gpio.c
3 *
4 * Created on: 20 mrt. 2025
5 */
10
11#include "gpio.h"
12#include "pinInterrupts.h"
13#include "timer.h"
14
20{
21 //Enable pull-up on PCB
22 P1DIR |= BIT3;
23 P1OUT |= BIT3;
24
25 //Stepper pins
26 P2OUT &= ~(STEPPER1 + STEPPER2 + STEPPER3 + STEPPER4); // Clear stepper pins output latch for a defined power-on state
27 P2DIR |= STEPPER1 + STEPPER2 + STEPPER3 + STEPPER4; // Set stepper pins to output direction
28
30
31 //fwdButton
32 P2DIR &= ~BIT1; // Input
33// P1REN |= BIT1; // Enable pull
34// P1OUT |= BIT1; // Enable pull up
35 P2IES &= ~BIT1; // low to high
36 P2IFG &= ~BIT1; // Clear flag
37 P2IE |= BIT1; // Enable interrupt
38 toggleFwdInterruptISR = 1; // Enable the ISR
39
40 //LED for lightning the clock
41 P1DIR |= BIT6; //LED0 as output
42 P1OUT &= ~BIT6; //Turn off LED0
43
44 //Indicator L
45 P1DIR |= BIT7; // Output
46 P1OUT &= ~BIT7; //Turn off
47
48 //EX-btn
49 P2DIR &= ~BIT2; // Input
50// P2REN |= BIT2; // Enable pull
51// P2OUT |= BIT2; // Enable pull up
52 P2IES &= ~BIT2; // low to high
53 P2IFG &= ~BIT2; // Clear interrupt flag
54// __delay_cycles(1000); // Small delay for stabilization otherwise a trigger is registered on boot up of dev board
55// P2IFG &= ~BIT2; // Clear it again
56 P2IE |= BIT2; // Enable interrupt
57
58 //DCF77 input
59 P1DIR &= ~BIT5; // Input
60 P1IES |= BIT5; // high to low, first trigger on a low going pulse to detect 1800 ms sync pulse after bit 58
61 P1IFG &= ~BIT5; // Clear interrupt flag
62 __delay_cycles(1000); // Small delay for stabilization otherwise a trigger is registered on boot up of dev board
63 P1IFG &= ~BIT5; // Clear it again
64 P1IE |= BIT5; // Enable interrupt
65
66 //5V converter
67 P1DIR |= BIT0; // Output
68 P1OUT &= ~BIT0; //Turn off
69
70 //See for ADC pin setup adc.c
71
72 __enable_interrupt(); // Enable global interrupts
73}
74
79void wakeUp()
80{
81 setupGpio();
82 P1OUT |= BIT0; //Turn on 5v supply so stepper can spin
84}
85
90void sleep()
91{
92 // Configure GPIOs to it's lowest power state
94 P2IE &= ~BIT1; // Disable interrupt fwdButton
95 P2IE &= ~BIT2; // Disable interrupt exButton
96 P1IE &= ~BIT5; // Disable interrupt DCF77
97
98 P1OUT = 0; // All P1.x reset
99 P1DIR = 0xFF; // All P1.x outputs
100 P2OUT = 0; // All P2.x reset
101 P2DIR = 0xFF; // All P2.x outputs
102 P3OUT = 0; // All P3.x reset
103 P3DIR = 0xFF; // All P3.x outputs
104
105 P2DIR &= ~BIT1; // Input fwdButton
106 P2DIR &= ~BIT2; // Input exButton
107 P1DIR &= ~BIT5; // Input DCF77
108
109 //Keep ADC pins as input
110 P1DIR &= ~BIT1; // Set P1.1 as input: Battery
111 P1DIR &= ~BIT2; // Set P1.2 as input: Ignition switch
112
113 setupClockIO();
114}
115
121{
122 //Clock
123 P2SEL |= BIT6 | BIT7; // Select XIN and XOUT functionality
124 P2SEL2 &= ~(BIT6 | BIT7); // Ensure secondary function is not selected
125}
void wakeUp()
Setup of all GPIO's after wakeup, gets called from ADC10_ISR(void)
Definition gpio.c:79
void setupClockIO()
Setup of the external clock pins, gets called from setupGpio(), wakeup(), sleep()
Definition gpio.c:120
void sleep()
Setup of all GPIO's after sleep, gets called from ADC10_ISR(void)
Definition gpio.c:90
void setupGpio()
Setup of all GPIO's on startup, gets called from main()
Definition gpio.c:19
bool toggleFwdInterruptISR
#define STEPPER2
Definition pins.h:14
#define STEPPER3
Definition pins.h:15
#define STEPPER4
Definition pins.h:16
#define STEPPER1
Definition pins.h:13
void sleepTimer0()
Definition timer.c:36
void wakeUpTimer0()
Definition timer.c:43